Flushing Radiator

I have a 94 SL2 Saturn and would like to know how flush the radiator
and system. I purchased the Prestone flushing tee and can not fiqure
out where to install it. Any help would be appreciated. Thank You.

 

Personally, I'd pitch it.

 

I agree with "Blah Blah". I've had Prestone tees go bad on two different
cars - they warp from heat causing a sever coolant leak.

I have a 1993 SL1. Easiest way to flush my car is to (after draining
radiator and capturing old coolant) remove the thermostat (in elbow were
lower radiator hose joins engine), open petcock at bottom left of radiator
and run water through the filler until it runs clear.

Assuming your 92 is similar to my 93, you need a tool to remove the
thermostat from the elbow. Tool comes with a new thermostat - cost, about
$15.00 at Advanced Auto. The tools is very simple; just a thick piece of
cardboard tubing about the diameter of a toilet paper core. With this, its
a snap to get the thermo out. Without it, I couldn't find a way.

Hardest thing is opening the damd petcock - a flat tab on a plug. You can
get at it from the top, but but you can't get grip that gives you any
leverage and its hard to turn; mine was, anyway. I made a tool by sawing a
slot in a 4"x4"x1" block of wood. It gave me the leverage I needed.

Good luck.
Gary

 

If I recall correctly, the tee is supposed to go into the heater core
inlet line.
It's the hose at the top rear of the engine
that goes from the intake manifold to the firewall.
It has curves in it and looks like it would be quite difficult to
install a tee
into, but you might be able to make it work.

 

You can also drain the block. The drain plug (bolt) is just under the
thermostat area. I do not remove the thermostat to do a flush.

Leave the radiator drain and block drain open. Put a garden hose in your
resevoir and turn it on just so it barely spills over. Then run the engine for
2-5 minutes or until the water coming out is clear. Shut the car off and then
shut the water off. Let the entire system drain. Then repeat several more
times.

James

 

I too agree with "Blah Blah" about the flush tees.
I was able to get a small munky-wrench on the petcock to open it.

But there are plenty of posts here about it, so i'm not gonna repeat what
everyone else said.

I did a flush a while ago, and have not found a place to dispose of the used
coolant. I would like to be "environmentally friendly", I've called around,
but no one will take it. Would a dealership take it? or is there some kind
of recycling center?

Thanks
Jeremiah

 

Yeah those petcocks can be a real hassle sometimes. A adjustable
crescent wrench works as well sometimes. Depends on the angle..

Some of the auto parts stores take such things. I know Autozone here
takes upto 5 quarts of oil a day per person. I cant remember if they
take coolant, haven't done that in awhile.

 

Doesn't the cold water close the thermostat?

 

Check your local water dept. I live in Columbus, OH and here it is
safe to flush a coolant in a toilet because they do something to the
sewer.

 

Doesn't the cold water close the thermostat?

Yes... that is why you open the eng block drain if you prefer not to remove the
thermostat.

James

 

We are on a municipal sewer and the local guidelines used to suggest
flushing used antifreeze down the sanitary sewer (not the storm drain). Now
Westchester county has semi-annual 'chemical collection days'. I can't see
storing stuff for up to 6 months before disposal. Here are some other
options

http://www.greentruck.com/waste/antifreeze/1102.html
http://www.health.state.nd.us/ndhd/environ/wm/pdf/Household_Auto0309.pdf
http://www.dtsc.ca.gov/PollutionPrevention/VSR/vsrfactsheets/Antifreeze-recycling02.pdf